Gainesville · Tile & grout

Shower Tile and Grout Cleaning in Gainesville, FL

Shower walls, shower floors, tub surrounds, and grout deep cleaned for Gainesville homeowners, landlords, and property managers, from Haile and the Millhopper area to rentals near campus and well-water homes out toward Newberry and Alachua.

What builds up in a Gainesville shower

Gainesville tap water comes from the Floridan aquifer, which runs through limestone, so it carries minerals that dry into a chalky haze on tile and glass. Those minerals react with bar soap and shampoo to form soap scum, which is tougher than either one alone. Add a long, sticky summer that keeps bathrooms damp, and the scum settles into porous grout where it darkens a little more every month.

Most people notice it first along the bottom rows and the shower floor, where water sits longest. Scrubbing harder with a household brush tends to polish the tile face while the grout stays gray. A specialty cleaning loosens what is inside the joints and rinses it out. For kitchens, entries, and the rest of the tile in your home, see Gainesville tile and grout cleaning.

Well water, rust-colored streaks, and orange grout

Many homes outside the city, around Newberry, Alachua, Archer, and High Springs, run on private wells. Iron in well water leaves orange and brown streaks on shower walls, around the drain, and in the grout, and some wells add a dark sulfur film on top. These stains are a common reason Alachua County homeowners call us about a shower that looks dirty a week after they scrub it. The same water often stains the floor grout too, so see Alachua tile and grout and Newberry tile and grout for whole-floor work out that way. White chalky spots are a different mineral problem; see white mineral spots and soap film.

We test a small area first and use products suited to mineral and iron staining that are safe for the tile in your shower. Surface staining usually clears well. Iron that has soaked deep into old grout can leave a faint tint, and we tell you up front which spots we expect to lift. Keeping the stains from coming back is a water treatment question, so if they return quickly, a well or water treatment specialist is the right next call. Our Newberry tile and grout page covers well-water homes in more detail.

How we clean a Gainesville shower

  1. Check the shower. Tile, stone, or cultured marble; grout and caulk condition; the drain; and any soft or hollow spots underfoot.
  2. Cover what stays dry. The vanity, the bathroom floor outside the shower, and the drain are protected before we begin.
  3. Let the cleaner work. A surface-matched product rests on the walls and floor long enough to soften scum, minerals, and any well-water staining.
  4. Detail the joints. Each grout line gets brushwork, along with niches, benches, the curb, the tub ledge, and the corners where buildup sits longest.
  5. Rinse and pull it out. Hot-water rinsing with vacuum recovery removes the loosened residue so it does not dry back into the grout.
  6. Walk through and plan sealing. We review the shower with you and talk through sealing once the grout is fully dry.

Student rentals and move-out showers

Gainesville rentals turn over on the academic calendar, and many units change hands within the same few weeks each summer. A shower that went a full lease without a deep cleaning often has layers of scum, product residue, and darkened grout that a regular turnover clean does not reach. We work with landlords and property managers to clean several units in a building in one visit, and we leave notes on any shower that needs caulk, grout repair, or a plumber before the next tenant moves in. More: rental turnover tile and grout guide · downtown and campus-area tile.

Showers in older and newer Gainesville homes

Older homes in NW Gainesville and near the Duckpond often have tiled tub surrounds with small wall tile and original grout that has seen years of scrubbing. These take slow, careful brushwork, and we keep an eye on joints that have softened with age. See NW Gainesville floor cleaning for the rest of the house.

Newer homes in Haile, along Archer Road, and in west Gainesville tend to have large porcelain tile, frameless glass, and walk-in showers with benches. Fewer grout lines, but long joints at the floor and around niches carry most of the soil, and textured floor tile holds onto residue. See Haile tile and grout and SW Gainesville and Archer Road.

Walk-in showers set up for easier access, with low curbs, grab bars, and fold-down seats, are common in homes where parents or grandparents live. They often get cleaned around rather than under, so we pay extra attention to the areas behind and below fixtures.

Travertine, marble, and cultured marble surrounds

Plenty of Gainesville apartments and older homes have cultured marble tub surrounds, which are a cast panel with a glossy coating, not stone and not grout. They need non-abrasive products, since scouring pads and abrasive erasers scratch the coating. Real travertine and marble are the opposite problem: they tolerate brushing but not acid, so vinegar and many hard water removers etch them. We confirm which surface you have before choosing a product, and we will tell you when dullness is etching or wear that cleaning cannot change. For travertine and slate floors elsewhere in the house, see Gainesville travertine and natural stone cleaning.

When a shower needs a repair first

Cleaning brings back the color of sound grout. It does not rebuild joints that are cracked, soft, or missing, and it does not fix tiles that move. A shower floor with crumbling grout at the drain, cracked joints along the curb, or tiles that sound hollow may have water getting behind the tile. If we find those signs, we show you and suggest a tile installer or plumber before we clean, and we can come back once the repair is done. Our guide on cleaning versus replacing tile covers the bigger decision.

Sealing grout after a shower cleaning

Sealing comes after the clean, never instead of it, and it only works on grout that has fully dried. We plan around that and tell you how long to keep the shower out of use while the sealer cures. Sealed shower grout resists soap and minerals longer and rinses clean more easily. Learn more on Gainesville grout sealing and in our tile sealing cycle tips.

Keeping it clean between visits

  • Squeegee walls and glass after each shower, especially in homes with hard city water or well water.
  • Wipe orange or brown well-water streaks while they are fresh; they are much easier to remove early.
  • Run the fan and leave the door open after showers during humid months.
  • Use non-abrasive products on cultured marble and acid-free products on travertine and marble.
  • Rinse cleaners off completely so residue does not become the next layer of film.

Fans, windows, and drying time in Gainesville bathrooms

How fast a shower dries decides how fast the grout darkens again. Gainesville's long, sticky season from late spring into fall keeps bathrooms damp, and the way a bathroom is built makes a big difference. Older homes around the Duckpond, the Northeast, and the 1960s to 1980s neighborhoods off NW 16th Avenue and Millhopper often have a window instead of an exhaust fan, or a small fan that moves very little air. Student apartments and rentals near campus, Midtown, and SW 20th Avenue often have a fan wired to the light, so it shuts off the moment the light does. Interior baths in newer Haile, Tioga, and SW Archer Road homes have no window at all, so the fan is the only way out for the steam. And when a home sits closed up over UF breaks or a summer away with the thermostat set high, the bathroom stays humid for days and the shower floor never fully dries.

At the end of every shower cleaning we wipe the walls, glass, and fixtures dry and leave the door open so the grout can finish drying before anyone uses it; for timing, see the FAQ below on using the shower again. After that, a few habits do the most good: run the fan for 15 to 20 minutes after each shower, or crack the window if there is no fan; squeegee the glass and the bottom rows of tile; leave the door and curtain open; and keep the air conditioning on a reasonable setting when you travel instead of shutting the house up hot. We do not repair or install fans. If the fan is noisy, barely pulls air, or you see peeling paint or water stains on the ceiling, that is a job for a handyman or an HVAC or electrical pro, and it is worth fixing before or after a cleaning so the results last. If water is getting behind the tile or under the curb, start with when a repair comes first. Sealing after the clean helps too: see sealing shower grout, and for rentals between leases, student rentals and move-outs. Questions? Call (904) 437-3832.

Walk-in and aging-in-place showers: benches, grab bars, and pebble or mosaic floors

Gainesville has a lot of homeowners who plan to stay put, and many have remodeled a hall or primary bath into a walk-in shower with a bench, grab bars, a handheld wand, and a low or no curb. You see these in established homes around NW 39th Avenue and Millhopper, Hidden Lake and Mile Run, Haile, and the 55-plus communities toward Jonesville and Newberry. They are built for safety, and they deserve a clean that keeps them safe. Pebble and small mosaic floors hold soap and body-wash film in deep, irregular joints, and that film can make a floor feel slicker than it should. Bench seats and the wall under grab bars collect residue where people brace and rinse.

We clean these showers with traction and comfort in mind. The floor gets worked joint by joint and rinsed until no cleaner residue is left behind, because a slick film is the last thing anyone wants on a shower floor built for safety. We detail around grab-bar flanges and the handheld hose without forcing anything loose, and we note any grout gaps at the bench or curb where water could get behind the tile. If you are keeping the shower ready for a parent or for yourself after surgery, tell us, and we will plan a visit that leaves the space dry and usable the same day when possible. Where repair shades have left the floor patchy, a grout color seal can even it out after the clean. Request a free walkthrough.

Tub-and-shower combos in hall and kids' baths

Not every Gainesville shower is a remodel. In most three- and four-bedroom homes, from Duckpond and the older neighborhoods near downtown to Tioga, Kanapaha, and the newer streets off SW 24th Avenue, the hall bath is still a tub with a tiled surround. That bath works hardest of all: kids' bath toys, bubble bath, foaming soaps, and splashing put residue on the lower three rows of tile and into the grout line where the tile meets the tub. Shower curtains trap moisture against the same strip, and that bottom joint is often the first place grout darkens and caulk starts to pull away.

We clean the full surround and give that tub-to-tile line extra attention, rinsing thoroughly so no residue is left in a tub where kids sit. Clean grout often reveals caulk that has shrunk or separated; we will point that out so it can be replaced, since a failing caulk line lets water behind the tile no matter how clean the grout looks. Many families have us do the hall bath, the primary shower, and the kitchen floor in one visit; see Gainesville tile and grout cleaning for the rest of the house, or read whether to clean or replace tired tile. Get an estimate here.

Shower floors and the area around the drain

The shower floor is usually the first part of a Gainesville shower to look tired. It gets standing water, soap and conditioner runoff, and foot traffic every day, so the grout lines there darken well before the walls do. The ring of grout around the drain is often the worst, because water collects there after every shower. Small floor tile also means far more grout per square foot than the walls.

We give the floor its own pre-treatment and dwell time, scrub the grout lines by hand and with rotary brushes, and rinse and extract so the residue goes down the drain, not into the grout. If the floor holds a puddle or a grout joint near the drain is cracked or hollow, we show you before we seal anything, since that is a repair question, not a cleaning one. More: Gainesville grout sealing · how often to reseal grout · Gainesville tile & grout cleaning.

Niches, shampoo ledges, and corners where water sits

Recessed niches, corner shelves, and the curb or threshold are where bottles sit and water lingers. Product drips, hard-water film, and soap scum build up on the flat surfaces, and the grout under the bottles stays wet longer than anywhere else in the shower. The inside corners where two walls meet collect the same buildup in a thin line that is easy to miss when you wipe down.

We clear the niches and ledges, work the flat surfaces and their back corners with detail brushes, and check the caulked joints at the corners, curb, and tub edge. Grout and caulk are different materials: if the caulk is split or peeling, we note it so it can be replaced rather than cleaned over. More: Gainesville travertine & natural stone for stone niches · Jacksonville shower tile cleaning · free estimate.

Gainesville neighborhoods and nearby towns

We clean shower tile across Gainesville and the towns around it. Local tile pages: Haile · Downtown and campus · NW Gainesville · SW Gainesville / Archer Road · Newberry Road · Newberry. Whole-home help starts at Gainesville floor care, or see every area we serve. On the Jacksonville side, see Jacksonville shower tile cleaning.

Proud to serve Gainesville

We are a family-owned company that has served Gainesville since 2019, and we take real pride in the homes and rentals we work in here. Every shower should end up cleaner than you expected, with clear guidance on what we did and how to keep it looking that way. Request a free estimate, call (904) 437-3832, or email contact@duvalfloorcare.com.

Pool, lanai, and outdoor-shower track-in: chlorine splash and sunscreen film indoors

Homes with a pool, screened lanai, or outdoor rinse often send a different soil into the nearest hall bath or mudroom shower than well-water orange staining or student-rental turnovers already covered above. Chlorine and pool-water splash dry into a chalky film on tile and glass, sunscreen and body oil leave a sticky haze on the lower walls and curb, and wet foot traffic from the lanai packs grit into the first rows of floor grout. That track-in pattern shows up in Haile, SW Archer, and NW Gainesville homes where the pool deck feeds straight toward an indoor shower used as a rinse station after swim days.

We treat it as its own soil stack: dry-vacuum grit from the floor joints, break down the oil-and-sunscreen film with a surface-matched cleaner, and rinse with vacuum recovery so residue does not dry back into the grout. Sealing after the clean helps the next swim weekend wipe up on those high-traffic floor joints, and we flag any cracked curb or soft joint that needs a tile installer before another wet season. Pair the visit with Gainesville grout sealing, start from Gainesville tile and grout for the rest of the house, and request a free estimate with a photo of the shower floor and the path from the lanai.

New subdivisions, Haile, SW Archer, and NW: first deep clean after builder dust

A first-year shower in a Haile, SW Archer, or NW Gainesville subdivision often still carries builder haze long after the punch list is signed. Fine thin-set dust and cutting residue settle into grout and textured floor tile, a chalky film dulls glass and glossy porcelain, and the first months of real showers lock that dust under soap and aquifer mineral spots. This is distinct from the well-water orange streaks and repair-first cases already covered above—it is a post-construction restore, not an iron-stain treatment or a cracked-grout referral.

Timing matters: the clean works best once painters and punch-list crews are done and you can keep the shower out of use long enough for grout to dry before sealing. We dry-vacuum fines from niches and floor joints first, then deep clean and extract so haze lifts instead of smears, and we tell you honestly when a rushed joint needs a regrout rather than another pass. See Gainesville grout sealing for seal timing and cleaning versus replacing tile when the surround has bigger issues. If the same new home has travertine floors or a stone foyer still chalky from builder dust, see the first clean after builder dust on our Gainesville travertine and natural stone page. Send a wide shot plus a close-up through the estimate form.

Getting a shower ready to sell or list

Bathrooms get looked at closely in listing photos and showings, and a shower with gray grout or cloudy glass can make a well-kept Gainesville home look tired. We see this before sales in Haile, Duckpond, and NW neighborhoods, and when owners are getting a parent's home ready in Newberry or Alachua. A professional clean often makes a bigger difference than people expect, and it costs far less than a regrout or a remodel.

We deep clean the tile, grout, and glass, then tell you plainly what is left: joints that need repair, caulk that should be redone, or a stained area that a color seal would even out. That way you or your agent can decide what is worth fixing before photos. If the rest of the house has tile too, see Gainesville tile and grout cleaning, and send a few photos through the estimate form with your listing date.

Glass doors, bottom tracks, and the grout line under the glass

A lot of what makes a Gainesville shower look neglected is not on the walls at all. It is at the glass. Sliding bypass doors, common in older homes around the Duckpond, NW Gainesville, and in many student rentals, ride on an aluminum bottom track that holds a shallow strip of water after every shower. Soap, hair, and the minerals in our aquifer water settle there into a gray paste, and the curb grout under that track stays damp longer than anything else in the bathroom. Frameless and semi-frameless enclosures in newer Haile, SW Archer Road, and west Gainesville homes have their own trouble spots: the clips or U-channel holding the fixed panel, the vinyl sweep along the bottom of the door, and the single grout line that runs directly under the glass. That joint gets splash from both sides and is almost impossible to reach with a household brush, so it is often the darkest line in an otherwise clean shower.

On the visit we detail the track with narrow brushes and vacuum recovery, clear the small drain slots so the track can empty on its own, clean the curb and the grout along and beneath the glass, and wipe down the glass edges and hardware. Fixture finishes matter here: matte black, brushed nickel, and oil-rubbed bronze can dull or spot under strong acid cleaners, so we choose products for the hardware as well as the tile and keep harsh chemistry off finished metal. We do not remove panels or adjust doors. If a sweep is torn, a track is loose, a hinge is sagging, or the sealant along the base of the glass has pulled away, we point it out so a glass company can take care of it, since water getting under the curb there is a bigger problem than dirty grout. Between visits, leaving the door open after a shower so the track can dry, squeegeeing the glass down toward the drain, and rinsing the track with a cup of water and a small brush once a week keep the paste from coming back. Related: well water and orange grout · walk-in showers and benches · when a repair comes first · sealing shower grout · caulked joints around glass · what household products do to grout.

1960s to 1980s tile showers: small tile, wide grout, and old sealers

Many older Gainesville homes, from the ranch houses near Hibiscus Park and Northeast to mid-century homes off NW 16th Avenue, still have their original small square tile and wide cement grout. That tile is often sturdy and worth keeping. The grout has decades of buildup, and some showers have old coatings or sealers that have yellowed or peeled and now trap dirt under them.

We test a small area first, remove old residue and coatings where they will come off safely, and clean the wide joints with brushes and controlled pressure so we do not wear them down. Then we tell you whether the original tile can look good again or whether some joints need regrouting first. A fresh seal afterward helps those wide joints stay clean. See Gainesville grout sealing and our guide to cleaning versus replacing tile.

Pink, green, and pastel tile baths in Duckpond, Northeast, and near UF

Some of the most distinctive bathrooms in Gainesville are the original ones. Around the Duckpond, in Northeast Gainesville and Hibiscus Park, and on the 1950s and 1960s streets of University Park and College Park near UF, plenty of homes still have their first tile bath: pink, mint green, powder blue, or butter-yellow wall tile, often with a black or maroon trim line, running as a wainscot around the whole room and up the tub wall. The tub is usually the original enameled steel or cast iron, sometimes in a matching color, and the soap dish, toothbrush holder, and towel bar are ceramic pieces set right into the tile. Owners who keep these baths tend to love them, and matching colored tile is hard to find today, so careful cleaning is worth far more than tearing it out.

A bath like that asks for different care than a modern surround. Abrasive pads and harsh acid products can dull an old enameled tub or a tile glaze, so we protect the tub and test a spot before the walls get a full clean. Colored glaze often shows fine crazing after decades, and we work the grout without scouring the tile face. White or bone grout between pink and green tile shows every gray line, so the grout gets most of our attention: the wainscot joints, the rounded cap along the top, and the corners of the built-in soap dish and towel bar where film collects. Many of these houses also have a window right in the tub wall. We clean the tile around it by hand and keep spray off the sill; a soft or peeling wood sill is a carpentry fix, not a cleaning one. Loose built-in fixtures or cracked pieces are a job for a tile setter, and we point them out before we start.

Older rental houses near campus often have these baths too, and a careful clean between leases keeps an original bath looking cared for instead of tired; see student rentals and move-out showers. For the wide cement grout and old sealers these baths often share, see 1960s to 1980s tile showers; for the hex and penny-round floors below them, see vintage tile in Duckpond and downtown homes; to even out grout that stays uneven after cleaning, see Gainesville grout sealing. In Jacksonville, see tub surrounds in older Jacksonville homes. Call (904) 437-3832 or request an estimate with a photo of the tub wall.

FAQ

Gainesville shower tile cleaning FAQs

Can you remove orange well-water stains from shower grout?

Surface iron staining usually clears well with the right product and a thorough rinse. Iron that has soaked deep into older grout can leave a faint tint, and we tell you up front which spots we expect to lift. If stains return quickly, a well or water treatment specialist can address the source.

Do you clean showers in Gainesville student rentals between leases?

Yes. We work with landlords and property managers during turnover season, can clean several units in one visit, and leave notes on any shower that needs caulk, grout repair, or a plumber. See our rental turnover guide.

How often should shower grout be professionally cleaned in Gainesville?

There is no single calendar. Showers used every day in humid months, and showers on well water, build up faster than a guest bath. After the first cleaning we suggest a realistic interval based on what we saw, and sealing can stretch the time between visits.

Can you clean a cultured marble shower surround?

Yes. Cultured marble is a cast panel with a glossy coating, so we use non-abrasive products and soft pads. We point out scratches or worn coating that cleaning cannot change.

Is shower cleaning safe for travertine and marble?

Yes, when the products are right. We confirm the stone and use acid-free, stone-safe cleaners, since acid etches travertine and marble. Cleaning does not remove existing etch marks.

Will my shower grout look new after cleaning?

Sound grout usually comes back much closer to its original color. Deep stains, iron that soaked in, and patched lines that never matched may stay visible, and cracked or missing grout needs a repair trade. We tell you what to expect before we start.

How soon can we use the shower again?

After a cleaning alone, usually as soon as it is rinsed and wiped down. If we seal the grout, we tell you how long the sealer needs to cure before the shower is used.

Do you clean shower tile in Jacksonville too?

Yes. See Jacksonville shower tile cleaning for Beaches condos, older Riverside and San Marco baths, and the rest of the Jacksonville area.

We have a pool or lanai. Can you clean chlorine splash and sunscreen film out of the indoor shower?

Yes. Pool and lanai track-in leaves a different stack than ordinary soap scum: chlorine haze, sunscreen and body-oil film, and wet-foot grit in the floor joints. We dry-vacuum first, deep clean with a surface-matched product, and rinse with vacuum recovery, then talk through sealing on those high-traffic joints. Request a free estimate or see Gainesville grout sealing and Gainesville tile and grout.

We just moved into a new Haile, SW Archer, or NW Gainesville home. Can you remove builder dust and haze from the shower?

Yes. New-subdivision showers often hold thin-set dust and a chalky film on tile and glass that a household wipe will not clear. We dry-vacuum fines, deep clean and extract, and plan sealing once the grout is dry—and we say so if a few joints need a regrout instead. Send photos on the estimate form, or read cleaning versus replacing tile and Gainesville grout sealing.

Can you clean a walk-in shower with a pebble floor and grab bars without making the floor slippery?

Yes. We work pebble and mosaic floors joint by joint and rinse until no cleaner residue is left, since leftover film is what makes a floor feel slick. We detail around grab bars and handheld wands without loosening anything and point out any grout gaps at the bench or curb. A grout color seal can even out patchy floors afterward. Request a free walkthrough.

Do you clean tub-and-shower combos in Gainesville hall and kids' bathrooms?

Yes. We clean the whole tiled surround and give the tub-to-tile grout line extra attention, then rinse well so nothing is left in the tub. If clean grout reveals shrinking or separated caulk, we will point it out so it can be replaced. Many families add the primary shower and kitchen floor in the same visit; see Gainesville tile and grout cleaning or get an estimate.

Can you clean our shower before we list our Gainesville home?

Yes. We deep clean the tile, grout, and glass, then tell you plainly what is left, such as joints that need repair or caulk that should be redone, so you can decide what to fix before listing photos. Share your listing date on the estimate form.

Our older home has its original small tile shower. Is it worth cleaning?

Often, yes. Original small tile is usually sturdy. We test a small spot, remove old buildup and failed coatings where they come off safely, clean the wide grout joints, and tell you honestly if any joints need regrouting before sealing.

Can you clean original pink or green bathroom tile without damaging it?

Yes. We test a small spot first, use products that are safe for older glazes, and work the grout with brushes instead of scouring the tile face. Fine crazing in an old glaze is permanent, and we point it out before we start. See pink, green, and pastel tile baths.

Is it safe to clean the tile around our original enameled tub?

Yes. We protect the tub, keep abrasive pads and harsh acid products off the enamel, and rinse it clean when the tile work is done. Chips or worn spots in old enamel are a refinishing question, not a cleaning one, and we will say so.

Our tub wall has a window. Can you clean the tile around it?

Yes. We clean the tile and grout around the window by hand and keep spray off the sill. If the sill is soft or peeling, we let you know, since that needs a carpenter before the tile around it will keep looking its best.

Why is the grout on our shower floor so much darker than the walls?

The floor gets standing water, soap runoff, and foot traffic every day, and small floor tile means far more grout. We give the floor its own pre-treatment, scrub the lines, and rinse and extract so the residue goes down the drain. See Gainesville grout sealing.

Do you clean shower niches, ledges, and the caulked corners?

Yes. We clear and detail the niches, shelves, and curb, and check the caulked corners. Caulk is not grout, so if it is split or peeling we point it out so it can be replaced rather than cleaned over.

Can you clean the bottom track of a sliding shower door?

Yes. We detail the track with narrow brushes and vacuum recovery, clear the small drain slots so it can empty, and clean the curb grout underneath. If the track is loose or the door sweep is torn, we point it out so a glass company can repair it. See glass doors and tracks.

Will your cleaners damage matte black or brushed nickel shower fixtures?

We check the hardware finish before we start and choose products for it, keeping strong acid cleaners off finished metal. If a fixture already shows worn or spotted finish, we point it out before any work begins.

Why is the grout line right under my shower glass darker than the rest?

That joint gets splash from both sides of the panel, stays damp the longest, and is very hard to reach with a household brush, so soap and minerals build up there first. A detail clean usually brings it back, and sealing afterward slows the next buildup.

Our bathroom has no exhaust fan. Will the grout stay clean after you clean it?

It will stay clean longer if the shower can dry. Crack the window after showers, leave the door and curtain open, squeegee the glass and bottom rows, and consider sealing after the clean. See fans and drying time.

How long should I run the bathroom fan after a shower?

About 15 to 20 minutes after each shower is a good habit, with the door left open. If your fan shuts off with the light, a timer switch from an electrician makes that easy.

We leave Gainesville over UF breaks or the summer. How should we leave the bathroom?

Dry the shower before you go, leave the door and curtain open, and keep the air conditioning on a reasonable setting rather than shutting the house up hot. A closed, humid bathroom keeps the grout damp for days.

More answers are on our full FAQ, or you can reach us through the contact page or email contact@duvalfloorcare.com.

Ready for a Gainesville shower you are glad to step into?

Proud of our work and this community, family-owned specialty care since 2019. (904) 437-3832 · contact@duvalfloorcare.com.

Message us or call (904) 437-3832